• Round bar standard Download
  • Square-shape steel standard Download
  • Plate steel standard Download
  • Billet standard Download
  • Flat bar standard Download
  • wire standard Download
  • tube standard Download
  • pipe standard Download
  • Forging standard Download
  • casting standard Download
  • sheet standard Download
  • round bar standard Download
  • coil standard Download
  • Bar stock standard Download
  • profiled bar standard Download
Home > Standard > ASTM A686 - 92(2010) standard

ASTM A686 - 92(2010)

ASTM A686 - 92(2010) standard Download, We provide the main countries around the ISO standard download, including: AISI(US),UNS(US),SAE(US),ASTM(US),AMS(US),ASME(US),MIL(US),FED(US),DIN(DEU),JIS(JPN),AFNOR(FR),B.S.(UK),SS(SWE),UNI(ITA).

Production specification

Round bar standard Download
Square-shape steel standard Download
Plate steel standard Download
Billet standard Download
Flat bar standard Download
wire standard Download
tube standard Download
pipe standard Download
Forging standard Download
casting standard Download
sheet standard Download
round bar standard Download
coil standard Download
Bar stock standard Download
profiled bar standard Download

ASTM A686 - 92(2010)

ASTM A686
Abstract

This specification covers chemical, mechanical, and physical requirements for available wrought carbon Tool steel products. These products, which include hot- or cold-finished bar, plate, sheet, rod, wire, or Forgings, are normally fabricated into tools, dies, or fixtures. The selection of a material for a particular application will depend upon design, service conditions, and desired properties. An analysis of each heat of steel shall be made by the manufacturer to determine the percentage of the elements specified and these values shall conform to the chemical composition specified by the reference material. The hardness of the specimen after the specified heat treatment shall meet the minimum hardness value for the particular type of steel prescribed by the reference material. Rockwell C tests should be used where possible but light load tests may be necessary on thin specimens. The macrostructure of a specimen representing the entire cross-sectional area in the annealed condition shall be prepared in accordance with the reference material. It shall exhibit a structure free of excessive porosity, segregation, slag, dirt or other nonmetallic inclusions, pipes, checks, cracks, and other injurious defects.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the Standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

 

1.1 This specification covers the chemical, mechanical, and physical requirements for available wrought carbon Tool steel products.

1.2 These products, which include hot- or cold-finished bar, plate, sheet, rod, wire, or Forgings, are normally fabricated into tools, dies, or fixtures. The selection of a material for a particular application will depend upon design, service conditions, and desired properties.

1.3 The values stated in inch-pound units are to be regarded as the Standard. The values given in parentheses are provided for information only.

 

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the Standard.
ASTM Standards

A370 Test Methods and Definitions for Mechanical Testing of steel Products
A388/A388M Practice for Ultrasonic Examination of steel Forgings
A561 Practice for Macroetch Testing of Tool steel Bars
A700 Practices for Packaging, Marking, and Loading Methods for steel Products for Shipment
E3 Guide for Preparation of Metallographic Specimens
E30 Test Methods for Chemical Analysis of steel, Cast Iron, Open-Hearth Iron, and Wrought Iron
E45 Test Methods for Determining the Inclusion Content of Steel
E59 Practice for Sampling Steel and Iron for Determination of Chemical Composition

Military Standard

MIL-STD-163 Steel Mill Products, Preparation for Shipment and Storage

Federal Standards

Fed.Std.No.183 Continuous Identification Marking of Iron and Steel Products


--------------------------------------------------------------------------------

Index Terms

 

Carbon steel--specifications; Carbon steel forgings--specifications; Carbon steel wire--specifications; Steel forgings--specifications; Steel Forgings (tool steel); Steel sheet/strip/plate--specifications; Tool steel--specifications;

 

 

--------------------------------------------------------------------------------

ICS Code

 

ICS Number Code 77.140.10 (Heat-treatable steels)

 

 

--------------------------------------------------------------------------------
DOI: 10.1520/A0686-92R10

ASTM International is a member of CrossRef.

Related hot word search:ASTM A686 - 92(2010) ASTM A686 - 92(2010) round bar,ASTM A686 - 92(2010) forging,ASTM A686 - 92(2010) sheet,ASTM A686 - 92(2010) coil,ASTM A686 - 92(2010) flat bar,ASTM A686 - 92(2010) pipe,ASTM A686 - 92(2010) Lrregular

Prev:TOOL STEELS-DIE STEELS
Next:ASTM A681 - 08